Training indoors

Sensors, smart trainer and treadmill.

Pairing sensors

Paired under Settings → Devices & sensors (smart trainer, heart-rate strap, power meter, cadence sensor). A paired sensor connects by itself whenever a session screen is open and the sensor is awake, also mid-session; a sleeping smart trainer wakes up when you start pedalling and connects shortly after.

If an indoor workout finds no trainer, it offers "Connect trainer". On the treadmill Latu connects only the heart-rate strap; outdoors it uses power meter, strap and cadence sensor, never a smart trainer; a tile shows only once its sensor connects on that ride. If a sensor does not show up: is it on, and not connected to another app?

Heart rate without a strap (iPhone app): under Devices & sensors → "Heart rate without a chest strap" you pick Apple Watch (the Latu app on the watch, watchOS 10 or later) or AirPods Pro 3 / Powerbeats Pro 2 (iOS 26), or Off; every session screen then takes it like a strap, indoors and out.

A strap counts first; the watch or earbuds step in after 5 seconds without it. Their values come about every 5 seconds, so the number moves less often than with a strap. Starting the watch ends a workout running in Apple's Workout app. Nothing is saved to Apple Health unless "Save to Apple Health" is on.

Workouts on the trainer

Before the start the screen shows what today is, the fueling and which sensors are there; the clock starts with the first pedal strokes, or with "Start now". The two big keys move the target by 5 W for the rest of the session (in a free ride the watts the trainer holds, or 0.5 % on a gradient).

Pause, skip, +1 min and finish act on a short hold, so sweat dripping on the screen does nothing; a tap that is too short shows "Hold" on the key; finishing then asks once more. The top shows the time ridden against the planned total. In the last 10 seconds of a part the next one grows, the last 3 count down, and a new part shows large; a rest can say about how much to have drunk by now (a suggestion, nothing to log); that reminder sits just above "Next", and both always stay in view.

The watt number is cyan within 5 % of the target the trainer is holding, orange at 5–15 % off, red beyond. A planned cadence range shows small under the live cadence, a planned pulse zone under the pulse (in bpm with a threshold heart rate); cyan like the watts inside it, soft orange with an arrow outside.

"Next" also names the coming block's cadence and pulse. Without a strap the pulse tile is "Connect strap". When a connected trainer or sensor stops sending, its tile shows "—" and Latu brings the values back on its own in the background, without a message. The profile draws the ridden watts over the plan.

The speaker key mutes the voice for this session; switched back on, it says so in one sentence. After finishing, a short end screen ("Done." for a session ridden to its planned end, "Finished." when it was stopped earlier or a block was skipped) shows the time, the measured averages and the ridden watts over the plan, then the recap.

Trainer sets it or shift yourself

In the briefing, and mid-ride by holding the target tile (which shows who sets the load; on its side also the worded key at the top), you pick "Trainer sets it" (the trainer holds the target watts and eases the load when the cadence collapses) or "Shift yourself": the trainer feels like a flat road, the targets stay on screen with their colours and countdowns, and you meet them with gears and cadence; what is recorded is what the legs pushed.

Switching back mid-interval climbs from the current watts. Latu remembers the choice on the phone; not offered for the ramp test. A free ride has its own modes (target watts, gradient, free). Pulse hold: in easy blocks of 8 minutes or more, "By pulse" (briefing, or holding the pulse tile) lets the trainer move the watts in 5 W steps so the pulse stays in the block's zone from the threshold heart rate, never more than 10 W above the plan.

Needs a strap, a threshold heart rate, pulse consent and "Trainer sets it"; without a pulse the watts stay fixed. A block can be planned with it ("Pulse hold" in the block editor). Only while Latu is on screen.

Auto-pause

On the trainer (workout or free ride), when neither power nor cadence moves for 5 seconds the session pauses by itself. "Auto-paused" shows; the clock, the parts, the countdown, the voice and the fueling times stand; a watt target the trainer holds drops to a light load, as with the pause key.

After either pause the target does not come back in one jump: it climbs from the light load over about 12 seconds (a line under the target shows where it climbs to and the seconds left; with the voice on, one short sentence); an easy part (60 % of FTP or less) comes back at once. Pedalling again carries on by itself, also when Latu is in the background.

A pause you pressed stays until you continue. No auto-pause during an FTP test (stopping ends the ramp test as before) and none without a trainer or a power or cadence sensor. Stopped time is not riding time: load, calories and averages use the time ridden. The treadmill has no auto-pause, because Latu gets no speed from the treadmill.

Treadmill

A planned run shows, part by part, the belt speed to set (from your own paces) with the pace; the two big keys move it by 0.5 for the rest of the run. Latu does not control the treadmill. A free run shows heart rate large. The distance is entered from the treadmill at the end; a short end screen then shows the time (with a distance also distance and pace), then the session's page.